Wi-Fi that keeps dropping at the office in Algeria (2027): the internet cuts out several times a day, how to tell the line from the Wi-Fi, coverage, wired access points, channels, roaming, backup link

“The internet cuts out several times a day. In the meeting room the video call freezes; in the warehouse the handhelds lose the connection; and now and then the whole office goes down at once. We added a repeater and it got worse. The operator says the line is fine, the installer says it is the line. Who do we believe, and what do we do?” Neither of them without a measurement. A computer plugged in by cable settles it in a day; a log of the drops does the rest.

Symloop13 min read
The Wi-Fi keeps dropping the line, or the Wi-Fi?A wired computer to settle it, a log of the drops, the signal room by room, wired access pointsWI-FI DROPPING · OFFICE · ALGERIA · 2027The Wi-Fi keeps droppingthe line, or the Wi-Fi?A wired computer to settle it, a log of the drops, the signalroom by room, wired access pointsA SINGLE BOX−84 dBm in the meeting roomTHREE WIRED POINTSsix rooms above the referencesymloop.com

Short answer. “It drops” covers four faults: the line or the box, coverage, saturation, roaming. To know which, plug a computer into the box by cable for a day: if it drops too, it is not the Wi-Fi. Note every drop for a week, with the time, the room and the device. Measure the signal room by room, with a phone. Then fix the cause, not the symptom: a backup link for the line, wired access points on the ceiling for coverage, consistent channels and settings for the rest. A repeater fixes none of them: it cuts wireless throughput by at least half.

This guide is for the manager of an office, a shop, a warehouse or a clinic whose connection keeps dropping, and for the founder based in France who hears their teams complain from a distance. The definitions and figures quoted come from public sources: Wi-Fi channels, the access point, the repeater, the 802.11r amendment, the ping utility, packet loss. The six-room floor and its measurements are a constructed example. This guide gives no hardware prices; to build a network from scratch, see the guide to installing a network.

Diagnose in this order

The first step is accented: test with a wired computer.

Figure 1 · The accented step is the first: a computer connected to the box by a cable, for a day. It tells you whether the fault is before the Wi-Fi or in the Wi-Fi. Nothing is bought before the third step; the sixth checks that the fix helped.

The wired computer. It is the test that settles the argument between the operator and the installer. A computer connected to the box by a cable, Wi-Fi switched off, left for a day with a continuous ping: ping is a utility used to test the reachability of a host on a network. Run two, one to the box, the other to a public address. If the second is interrupted and not the first, it is the line. If neither is interrupted while the Wi-Fi drops, it is the Wi-Fi.

The log. A sheet next to each desk, or a message in a group: the time, the room, the device. After a week the pattern reads by itself: always the meeting room, always around ten o'clock, always while walking to the warehouse. The measurement. The signal is read on a phone, in dBm: the closer the figure is to zero, the better. A common reference for voice and video calls is −67 dBm; one manufacturer's documentation, Cisco Meraki, also recommends for data a signal-to-noise ratio of 20 dB or more.

«A computer plugged in by cable settles in a day what the operator and the installer have been blaming on each other for months.»
01

The line or the Wi-Fi: three questions to find out

The figure sorts the four faults behind three questions.

Figure 2 · Three questions, in order. A wired computer that drops too points to the line or the box. Otherwise, drops limited to certain rooms point to coverage; drops everywhere point to saturation at busy hours, or to roaming when you move around. A schematic tree from a constructed example.

If the wired computer drops too. Packet loss occurs when packets of data travelling across a network fail to reach their destination: here, it happens before the Wi-Fi is even involved. Three suspects. The operator's line: send them your dated log, not an impression. The box: it overheats, restarts, or its power supply suffers brief power cuts, which a UPS solves. Finally the cabling, or a faulty switch between the box and the computer.

If only the Wi-Fi drops. Two questions remain. In certain rooms only: it is coverage. Everywhere: at busy hours, it is saturation; while moving around, it is roaming. When everything adds up. In an office that has grown around a single box, several causes are often found at once; you then start with the line and coverage, and measure again.

02

The same floor, one box in the entrance or three access points on the ceiling

The figure gives the signal read in six rooms, before and after.

Figure 3 · The same six-room floor. With one box in the entrance, the meeting room is at −84 dBm, the storeroom at −81 and accounts at −70: three rooms below the common reference of −67 dBm. With three wired access points on the ceiling, all are between −49 and −56. Invented values for a constructed example.

Coverage. In the example, the box is in the entrance. Reception is at −48 dBm, the meeting room at −84, the storeroom at −81: that is where calls break up. The 5 GHz bands are absorbed to a greater degree by common building materials than the 2.4 GHz bands, and usually give a shorter range: the fastest band is also the one that gets through walls least well.

The access point, not the repeater. A repeater takes an existing signal from a router or access point and rebroadcasts it: it repeats a signal that is already weak, and wireless throughput is reduced by at least 50 %. An access point is a networking device that allows Wi-Fi devices to connect to a wired network: you bring it a cable, which can also power it, and fit it on the ceiling, from a measurement. With three access points, the six rooms move to between −49 and −56 dBm.

03

Six causes, how to recognise them, what to do

The figure gives, for six causes, their signature and the remedy.

Figure 4 · Six causes, from the furthest upstream to the finest. Each has a signature: a moment, a place, a message. That is why the log of drops is worth more than a purchase: it says which of the six you have.

Too many devices, a crowded channel. An access point shares its time among all the devices talking to it: a full meeting room saturates it. The 2.4 GHz band has fourteen channels, spaced 5 MHz apart, of which only three do not overlap at the usual width: 1, 6 and 11. It is also the band of microwave ovens. Two neighbouring access points on the same channel get in each other's way. The Wi-Fi 6 standard was designed to support dense deployments; it helps, but replaces neither one more access point nor well-spread channels.

Addresses. The box lends each device an address for a set time. When the pool is empty, newcomers see “connected, no internet”: it happens in the morning, in a place open to the public, when the lease is too long. And two devices set by hand to the same address cut each other off. Roaming. A phone stays attached to the access point it is leaving for as long as it answers at all. An amendment to the standard, 802.11r, is there to permit continuous connectivity for devices in motion; it assumes the same network name and the same settings on every access point. That is what keeps a call alive on IP telephony while you walk.

04

A network that does not drop, in five layers

The accented layer is the access points.

Figure 5 · The accented layer is the access points: their number and place, decided from a measurement. But it only holds on the first two, a doubled line and one cable per access point, and only gives its full effect with the last two.

The line. A second link, from another operator and if possible on another technology, with automatic failover: the outage of the first is no longer noticed. Between two sites, it is also the condition for a stable link, see the guide to connecting two sites. Cabling and access points. Each access point has its own cable back to the rack, and gets its power over that cable: Power over Ethernet passes electric power along with data on the same cabling.

Settings and separation. Channels spread out, power adjusted so that access points overlap without smothering each other, roaming switched on. Guests are on their own network, with limited speed, as in the guide to filtering. And what must never drop, tills, fixed computers, printers, is on cable: Wi-Fi is for what moves. If, with all that done, the software is still slow, look at the server: see the guide to the slow server.

«What must never drop is on cable: Wi-Fi is for what moves.»
05

Four weeks, from the first test to the second reading, in 2027

Four weeks in the example, the first without buying anything.

  • What the manager receives: the result of the wired test, a week's log of drops, the signal measured room by room, the cause identified among the six, then the same measurements after the fix.
  • What the company no longer does: buy one more repeater, leave the operator and the installer blaming each other, hold its video calls in the one room with no signal, put the till on Wi-Fi.
  • What is measured: drops per day and per room, signal in each room, line outages seen from the wired computer, devices per access point at busy hours.
  • What Symloop does: the test and the log, measurement on a floor plan, cabling and fitting the access points, the settings, the guest network, the backup link and its failover, then the second reading.
Figure 6 · Four weeks in the example. The accented period is the first: a test and a log, without buying anything. The fourth repeats the same measurements: you then know what the fix changed. Indicative durations from a constructed example.

Week 1, the test and the log. Nothing is bought. Week 2, the line and the box: log passed to the operator, box protected or replaced, backup link studied. Weeks 2 and 3, cables and access points.

Week 3, settings and separation. Week 4, the second reading: same sheets, same measurements, and the comparison. If the office is already cabled, two weeks are enough; if cables have to be pulled through partitions, allow more.

Why does the Wi-Fi keep dropping at the office?
For one of four reasons: the line or the box drops, the signal is too weak in certain rooms, too many devices share an access point or a channel, or the device stays attached to an access point that is too far away. A wired computer and a week's log tell you which.
Why does the internet cut out so often?
If everything drops at once, the wired computer included, the cause is before the Wi-Fi: the operator's line, a box that overheats or restarts, or its power supply. If only wireless devices drop, it is the Wi-Fi. The test takes a day.
How do I know whether the problem is the operator or my own set-up?
Connect a computer to the box by cable and leave it for a day with two continuous tests, one to the box, the other to the internet. If the second is interrupted, it is the line: send the dated log to the operator. If not, it is your set-up.
Does a Wi-Fi repeater solve the problem?
Rarely. It rebroadcasts a signal that is already weak, and wireless throughput through it is reduced by at least half. The answer to a badly covered room is an access point connected by a cable, placed from a measurement.
How many Wi-Fi access points does an office need?
The number comes from a measurement, not from floor area alone: it depends on the walls, the number of devices and what they are used for. In our example, three access points cover six rooms. Measure the signal room by room before deciding.
Why does the Wi-Fi work near the box and not in the meeting room?
Because every wall absorbs part of the signal, and the fastest band is the one that gets through least well. In our example, it goes from −48 dBm at reception to −84 in the meeting room, well below the common reference of −67.
What does “connected, no internet” mean?
The device is linked to the access point, but has not received a usable address, or the line is down. If it only happens to newcomers, in the morning, the box's pool of addresses is used up: it is widened and the lease is shortened.
Should we move to a newer Wi-Fi standard?
Not first. A recent standard fitted on a badly placed box changes nothing in the room at the back. It helps when many devices share an access point, once coverage and channels are sorted.
Do we need a second internet subscription?
Yes, as soon as an hour without a connection costs an hour of work or sales. A second link from another operator, with automatic failover, makes the outage of the first invisible. It is decided after the wired test, which says how often the line goes down.
How long does it take to fix Wi-Fi that keeps dropping?
Four weeks in our example: one of testing and logging without buying anything, two for the line, the cables and the access points, one for the settings and the second reading. Two weeks if the office is already cabled.
Tell us how many rooms, how many devices, and where it drops: we run the wired test and the log, and within a week you will know whether it is the line or the Wi-Fi

Video calls that freeze, handhelds that drop in the warehouse, repeaters piled up, operator and installer blaming each other, or a founder in France hearing it from a distance: we measure, fix the cause, and measure again

Wired test, log, measurement on a floor plan, cabling, access points, settings, guest network, backup link. We work from Algiers and Sétif, in French, Arabic and English.